Description
When using LightBurn with the HEXA RF Open-Bottom Engraving module, you can engrave long objects that exceed the work area segment by segment.
The workflow is the same as Passthrough Engraving in Beam Studio: engrave two triangle alignment marks with each segment, then use the marks to align the material manually before engraving the next segment.
| Note: The HEXA RF cannot report the laser head position to LightBurn in real time, so LightBurn's "Print and Cut" auto-alignment feature is not supported. Please follow the steps in this article. |
Limitations
Due to the physical limitations of the machine's open-bottom slot, it is recommended that the material width does not exceed 500mm for HEXA RF, and 350mm for Beambox II while the length is unlimited.
Before You Start
- Please ensure the Open-Bottom Engraving module is correctly installed.
Refer to the "Open-Bottom Hardware Installation Guide".
If you have already completed the installation, please skip this step. -
For connecting the machine to LightBurn, refer to the articles below according to your model.
Step 1 - Set the Start From Mode
In the Laser window, set "Start From" to "Absolute Coords".
Every segment is engraved at the same position in the work area. Only the material moves; the design position stays the same.
① Start From: select "Absolute Coords"
Step 2 - Prepare the Segments and Alignment Marks
Step 2.1 - Import or Draw the Object
Import the object and adjust its size. The example below uses a long rectangle drawn with the "Create Rectangle" tool (Ctrl+R). The object is about 450mm long, which exceeds the HEXA RF work area.
① Create Rectangle tool
Step 2.2 - Add Alignment Marks
Use the "Create Regular Triangle" tool on the left toolbar to draw triangles with sides of about 4cm as alignment marks. Place one set at the top edge and one set at the bottom edge of the first segment. The distance between the two sets is the height of each segment.
The alignment marks must be engraved across the main material and the auxiliary material, straddling the boundary between the two boards.
① Create Regular Triangle tool ② Alignment marks (one set at the top edge, one set at the bottom edge)
Step 2.3 - Divide the Object
Click the scissors icon on the left toolbar (① in the figure below) and cut the object at the position of the bottom alignment marks.
In this example, the object is about 450mm long and each segment is about 250mm high, so the object is divided into two segments. It is generally recommended to minimize the number of segments to avoid potential misalignment at the connection points.
① Scissors tool ② Segment 1 (with top and bottom alignment marks)
Step 2.4 - Save Each Segment as a Separate File
After laying out each segment, press Ctrl+S (⌘+S on Mac) to save it as a separate file, for example "Segment 1" and "Segment 2". When saving Segment 1, delete the graphics of Segment 2 first; when saving Segment 2, delete the graphics of Segment 1 (keep the top alignment marks).
After cutting, Segment 2 stays in its original position, partly outside the work area. Before saving, move Segment 2 up so that its top alignment marks sit at the same position as the top alignment marks of Segment 1. This way, all segments are engraved at the same position in the work area.
① Segment 2 after cutting (original position, before moving)
Step 3 - Engraving Job
Step 3.1 - Preparation for Engraving
Secure the auxiliary material next to the main material.
Open the Segment 1 file and click "Frame" in the Laser window. The laser head traces the engraving boundary with the beam off.
Use the frame preview to confirm that the alignment marks straddle the main material and the auxiliary material.
① Frame: traces the cut boundary with the laser head (beam off)
Step 3.2 - Engrave Segment 1
After adjusting the parameters, start engraving Segment 1.
After engraving, part of the alignment marks should be on the auxiliary material.
For a photo of the result, refer to Step 4.2 of 3-3 HEXA RF - Passthrough Engraving Guide. The hardware and operation are the same.
Step 3.3 - Engrave Segment 2
Move the main material so that its bottom alignment marks line up with the top marks on the auxiliary material.
Open the Segment 2 file, confirm the position with Frame, and engrave Segment 2.
If there are more segments, repeat Step 3.3.
For a photo of the alignment, refer to Step 4.3 of 3-3 HEXA RF - Passthrough Engraving Guide. The hardware and operation are the same.
#END
Comments
0 comments
Article is closed for comments.